Zhengzhou Chorus Lubricant Additive Co.,Ltd.

Home> Blog> Microemulsion cutting fluid the most practical and comprehensive use of process rules, good good!

Microemulsion cutting fluid the most practical and comprehensive use of process rules, good good!

April 13, 2024
Microemulsion cutting fluid the most practical and comprehensive use of process rules, good good!

This regulation specifies the acceptance, storage conditions, use and maintenance, scrap indicators, replacement methods, etc. of the microemulsified cutting fluid, which is most conducive to the correct use of microemulsified cutting fluid.

p

1, into the factory acceptance

Each batch of products into the factory should be in accordance with the relevant indicators of this standard acceptance, unqualified, strictly prohibited use.

p

2. Put in inventory

After the cutting fluid enters the factory, it should be stored in the warehouse. To avoid the sun, rain, frost and other adverse external climate.
p
3. Use and maintenance

Dilution of microemulsified cutting fluid

1) Dilute water should be used white water or other purified water equivalent to tap water: such as the concentration of Ca and Mg ions in dilute water >350ppm. Water softening treatment should be carried out.

2) Diluent concentration control should be based on the volume of the water tank (pool), according to the use of product concentration measurement: in the process of use, should be based on the processing situation, regularly according to the initial concentration of 1/4~1/2 added to ensure the specified use of concentration.

Maintenance of microemulsified cutting fluid

1) The microemulsified cutting fluid should be maintained, and the liquid tank (pool) should have good ventilation and light transmission conditions: closed water tank (pool) circulation system. Fresh air and light are blown into the liquid tank (pool) regularly every day.

2) Maintain the normal pH value of regular sampling of microemulsion diluent pH value should be maintained within the specified range, such as pH value less than 8, should be added new liquid or with triethanolamine or sodium carbonate to adjust the pH value >8.

3) Maintain the diluent clean chips require magnet adsorption, filter paper (cloth) filtration, centrifuge separation and other measures to purify the diluent.

4) If necessary, add fungicide.

5) Regular sampling of diluent main monitoring indicators, unqualified. Immediate measures should be taken or replaced.

p

4. Replacement

Scrap index of microemulsified cutting fluid

If any of the following circumstances. Should be replaced in time.

1) The rust resistance is significantly decreased: that is, the workpiece is easy to rust. Diluent sampling. The rust resistance is not qualified, and after increasing the concentration, the rust resistance is still unqualified.

2) Dilution deterioration: that is, large odor, odor, etc., total number of bacteria ≥108 / mL.3) Diluent pH <8.4) Diluent oil content ≥5%.

Alternative method

1) Before replacement, it is necessary to add fungicide to the waste liquid or after reasonable treatment before discharge.

2) When replacing, the waste liquid in the cutting area, pipeline and water tank (pool) of the machine tool must be thoroughly drained and rinsed before the new liquid can be replaced.
Contact Us

Author:

Mr. James

Phone/WhatsApp:

8613783582233

Popular Products
You may also like
Related Information
Is the higher the drop point of the grease, the better? How to identify the temperature resistance of grease?

Is the higher the drop point of the grease, the better? How to identify the temperature resistance of grease? When discussing the performance of grease, the drop point, as an important physical...

How much gas is the best time to fill up your car?

How much gas is the best time to fill up your car? In daily driving, mastering when to refuel the car is an important skill that affects both driving safety and vehicle maintenance. Many drivers may...

Source analysis and detection method of bearing grease pollution

Source analysis and detection method of bearing grease pollution The pollution of bearing grease is one of the key factors affecting bearing performance and service life, and its pollution sources...

Can the Fed's emergency rate cut stimulate the weak lubricants market?

Can the Fed's emergency rate cut stimulate the weak lubricants market? In September 2024, the Federal Reserve announced a policy change that caught the attention of the market - the target range of...

Related Categories

Email to this supplier

Subject:
Email:
Message:

Your message must be betwwen 20-8000 characters

Send Inquiry

Tel:0086-371-58651986

Fax:

Mobile Phone:8613783582233Contact me with Whatsapp

Email:sales@cn-lubricantadditive.com

Address:No.11 Changchun Road, High-Tech Zone, Zhengzhou, Henan

Mobile Site

Home

Product

Whatsapp

About Us

Inquiry

We will contact you immediately

Fill in more information so that we can get in touch with you faster

Privacy statement: Your privacy is very important to Us. Our company promises not to disclose your personal information to any external company with out your explicit permission.

Send